Air Compressor Specifications
| Pressure | 9-12 / 130-174 bar |
|---|---|
| Lubrication | ISO VG#15 |
Troubleshooting
8Fault codes
| Code | Meaning | Cause | Remedy |
|---|---|---|---|
| A | The hydraulic piston is not rising up with or without load | 1. Not enough air pressure supply to the jack 2. hydraulic piston is missing oil 3. Failure of the pneumatic pump | 1.a Supply air pressure within the tolerances specify into the manual and on the product nameplate 1.b Confirm the pneumatic hoses are correctly connected to the tie-ins (Fig.02) 2.a fill-in tank with recommended hydraulic oil (ISO VG#15) 2.b failure of the hydraulic system, product to be repair by authorized repair center 3. Product to be repaired by authorized repair facility |
| B | The hydraulic piston is not reaching the maximum position | Hydraulic piston is missing oil | Fill-in tank with recommended hydraulic oil (ISO VG#15) |
| C | The hydraulic piston cannot stand in upper position | 1. hydraulic piston is leaking oil. 2. Failure of the pneumatic pump | 1. Check the product to detect potential oil leakage from the piston. Send the product to authorized repair facility for reparation 2. Product to be repaired by authorized repair facility |
| D | The hydraulic piston is not going down | 1. Not enough air pressure supply to the jack 2. Failure of the pneumatic pump 3. Air leakage from the dustproof gasket | 1.a Supply air pressure within the tolerances specify into the manual and on the product nameplate 1.b Confirm the pneumatic hoses are correctly connected to the tie-ins (Fig.02) 2.&3. Product to be repaired by authorized repair facility |
Symptoms & remedies
| Symptom | Cause | Remedy |
|---|---|---|
| Der Hydraulikkolben fährt mit oder ohne Last nicht heraus. | 1. Luftdruck ungenügend für den Heber 2. Ölmangel im Hydraulikkolben 3. Störung der Pneumatikpumpe | 1.a Die Druckluftversorgung muss den Angaben in der Anleitung und dem Typenschild auf dem Produkt entsprechen. 1.b Prüfen Sie die Anschlüsse der Druckluftleitung an Anschlüssen (Fig.02) 2.a Passendes Öl in den Tank einfüllen (ISO VG#15) 2.b Störung im Hydrauliksystem, Produkt muss von einem autorisierten Reparaturzentrum geprüft werden 3. Produkt muss von einer autorisierten Werkstatt repariert werden |
| Der Hydraulikkolben erreicht nicht die maximale Position. | Ölmangel im Hydraulikkolben | Tank mit empfohlenen Hydrauliköl befüllen (ISO VG#15) |
| Der Hydraulikkolben verbleibt nicht in der oberen Stellung. | 1. Ölleck am Hydraulikkolben 2. Störung der Pneumatikpumpe | 1. Produkt auf Öllecks am Kolben prüfen Produkt an eine autorisierte Werkstatt zur Reparatur schicken 2. Produkt muss von einer autorisierten Werkstatt repariert werden |
| Der Hydraulikkolben fährt nicht zurück. | 1. Luftdruck ungenügend für den Heber 2. Störung der Pneumatikpumpe 3. Druckluftverlust an der Staubdichtung | 1.a SDie Druckluftversorgung muss den Angaben in der Anleitung und dem Typenschild auf dem Produkt entsprechen. 1.b Prüfen Sie die Anschlüsse der Druckluftleitung an Anschlüssen (Fig.02) 2.&3. Produkt muss von einer autorisierten Werkstatt repariert werden |
Fault codes and symptom→remedy steps extracted from this unit’s service/owner documentation; verify against the official manual before servicing.
Available documents
Service manual
About
Chicago Pneumatic CP85031 — air compressor. Specifications and parts compiled from manufacturer documents.