Engine
| Displacement | 2.9 L |
|---|---|
| Cylinders | 4 |
| Aspiration | Turbo Charged |
| Rated speed | 1800 rpm |
| Oil capacity | 8.5 L |
Troubleshooting
7Symptoms & remedies
| Symptom | Remedy |
|---|---|
| Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. | Engine should be turned off for safety during troubleshooting and maintenance, except when necessary. |
| Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors. | Ensure proper ventilation to avoid inhaling harmful exhaust gases. |
| Do not add the fuel near an open flame welding arc or when the engine is running. | Avoid adding fuel in proximity to flames or while the engine is operational. |
| Stop the engine and allow it to cool before refueling to prevent spilled fuel from vaporizing on contact with hot engine parts and igniting. | Allow the engine to cool before refueling to avoid ignition of spilled fuel. |
| Do not spill fuel when filling tank. If fuel is spilled, wipe it up and do not start engine until fumes have been eliminated. | Prevent fuel spills and ensure all fumes are cleared before restarting the engine. |
| Keep all equipment safety guards, covers and devices in position and in good repair. Keep hands, hair, clothing and tools away from V-belts, gears, fans and all other moving parts when starting, operating or repairing equipment. | Maintain safety guards and keep body parts clear of moving parts during operation and maintenance. |
| In some cases it may be necessary to remove safety guards to perform required maintenance. Remove guards only when necessary and replace them when the maintenance requiring their removal is complete. Always use the greatest care. | Remove safety guards only when absolutely necessary, replace them promptly after maintenance, and exercise caution. |
Fault codes and symptom→remedy steps extracted from this unit’s service/owner documentation; verify against the official manual before servicing.
Parts
20| Part # | Description | Qty | System | |
|---|---|---|---|---|
| S700162 | ef Valve | 1 | Air filter | buy |
| K126-12 | KP1696-1 Drive Roll Kit - Includes: 2 V groove drive rolls and inner wire guide for Steel Wires. (Used on LN-25 Pro) Drive Roll and Guide Tube Kit For .068-.072 in. (1.7-1.8 mm) cored or solid steel wire. | Service part / kit | buy | |
| K1478-5 | 1 | Service part / kit | buy | |
| K1797-xx | CABLE | 1 | Service part / kit | buy |
| K1816-1 | Full KVA Adapter Kit - Plugs into the 120/240V NEMA 14-50R receptacle on the case front (which accepts 4-prong plugs) and converts it to a NEMA 6-50R receptacle (which accepts 3-prong plugs) for connection to Lincoln Equipment with a NEMA 6-50P plug | 1 | Service part / kit | buy |
| K2614-9 | K126™PRO Innershield® Gun For self-shielded wire with 15 ft. (4.5 m) cable. For .062-5/64 in. (1.6-2.0 mm) wire. Includes K466-10 Connector Kit. | Service part / kit | buy | |
| K2636-1 | 1 | Service part / kit | buy | |
| K2639-1 | FENDER & LIGHT KIT | 1 | Service part / kit | buy |
| K2640-1 | CABLE STORAGE RACK | 1 | Service part / kit | buy |
| K2641-2 | FOUR WHEELED STEERABLE YARD TRAILER For in plant and yard towing. Comes standard with a Duo-Hitch™, a 2” Ball and Lunette Eye combination hitch. | 1 | Service part / kit | buy |
| K2642-1 | 1 | Service part / kit | buy | |
| K2808-1 | AIR VANTAGE® 600 SD C-3 NOTES AIR VANTAGE® 600 SD C-4 NOTES AIR VANTAGE® 600 SD D-1 MAINTENANCE | Service part / kit | buy | |
| K3985-1 | SPARK ARRESTOR KIT - Easily mounts to D.O.C. unit in place of the exhaust outlet pipe. | 1 | Service part / kit | buy |
| K487-25 | K2652-2-10-45 K487-25 Magnum SG Spool Gun Hand held semiautomatic wire feeder. Requires SG Control Module and Input Cable. | Service part / kit | buy | |
| K488 | SG Control Module The Interface between the power source and the spool gun. Provides control of the wire speed and gas flow. For use with a spool gun. | Service part / kit | buy | |
| K691-10 | Input Cable (For SG Control Module) For Lincoln engine power sources with 14-pin MS-type connection, separate 115V NEMA receptacles and output stud connections. | Service part / kit | buy | |
| K704 | ACCESSORY SET - Includes 35 feet (10 m) of electrode cable and 30ft. (9m) of work cable, headshield, Filter plate, work clamp and electrode holder. Cable is rated at 500 amps, 60% duty cycle. | 1 | Service part / kit | woodline $1292.82 |
| K802N | POWER PLUG KIT - Provides four 120V plugs rated at 20 amps each and one dual voltage, full KVA plug rated at 120/240V, 50 amps. 120V plug may not be compatible with NEMA common household receptacles. | 4 | Service part / kit | buy |
| K857 | 25 ft. (7.5 m) or K857-1 100 ft. (30.4 m) REMOTE CONTROL - Portable control provides same dial range as the output control on the welder from a location up to the specified length from the welder. Has convenient plug for easy connection to the welder. The AIR VANTAGE® 600 SD is equipped with a 12-pin connector for connecting the remote control and 12-pin to 6-pin adapter. | 1 | Service part / kit | buy |
| T12153-9 | Full-KVA Power Plug - One dual voltage plug rated at 120/240V, 50 amps, single phase. | 1 | Service part / kit | buy |
Service & wear parts shared with every machine that uses this engine. Confirm the exact part for your serial number.
Common questions
What engine does the Lincoln Electric 600 SD use?
The Lincoln Electric 600 SD welder is powered by the Deutz TD2.9L4 engine.
About
Lincoln Electric 600 SD — welder. Specifications and parts compiled from manufacturer documents.